AnalogLamb DEV-IOT00004 - DT-BL10-BL602 RISC-V WiFi&BT Board

-

 

DT-BL10 - BL602 RISC-V WiFi&BT Board

Overview

BL602 is an 32-bit RISC-V WiFi and Bluetooth LE SoC for low-power IoT applications. Moreover, variety of security features are supported. Peripheral interfaces include SDIO, SPI, UART, I2C, IR remote, PWM, ADC, DAC, ACOMP, PIR, etc. Flexible GPIO configurations are supported. BL602 has total 16 GPIOs.

BL602 BL604 RISC-V WiFI & Bluetooth SoC

Chip Specifications:

  • MCU subsystem – 32-bit RISC-V CPU with FPU with dynamic frequency from 1MHz to 192MHz, L1 cache
  • Memory – 276KB SRAM on-chip
  • Storage
    • 128KB ROM, 1Kb eFuse, and optional Embedded Flash on-chip
    • XIP QSPI flash support
  • Wireless
    • Wi-Fi 4 – 802.11 b/g/n @ 2.4 GHz
    • Bluetooth 5.0 LE
    • Wi-Fi Fast connection with BLE assistance
    • Wi-Fi Security – WPS/WEP/WPA/WPA2/WPA3
    • STA, SoftAP, and “sniffer” modes
    • Integrated RF balun, PA/LNA
    • WiFi Tx: 21 dBm; WiFi Rx: -98 dBm
  • Peripherals and I/Os
    • SDIO 2.0 slave (AP-Host)
    • SPI master/slave, 2x UART, I2C master/slave, 5x PWM channels
    • ADC – 10-bit general DAC, 12-bit general ADC, 2x general analog comparators
    • PIR (Passive Infra-Red) detection
    • IR remote HW accelerator
    • 16x flexible GPIOs (BL602) / 23x flexible GPIOs (BL604)
    • 4x DMA channels
    • RTC timer up to One year
    • 2x 32-bit general-purpose timers
  • Clocks – Supports XTAL 24/26/32/38.4/40MHz, XTAL 32/32.768KHz, internal RC 32KHz & 32MHz oscillator, internal system PLL
  • Security
    • Secure boot
    • Secure debug
    • XIP QSPI On-The-Fly AES Decryption (OTFAD)
    • AES-128/192/256
    • SHA-1/224/256
    • TRNG (True Random Number Generator)
    • PKA (Public Key Accelerator)
  • Debugging – JTAG
  • Supply Voltage – 2.1 to 3.6V
  • Low power modes – Off, hibernate, power down sleep, and active
  • Power consumption – Deep sleep: 0.5uA; WiFi Rx: 18 mA
  • Package Type – 32-pin QFN (BL602) or 40 pin QFN (BL604)
  • Temperature range – -40°C to 125°C

Board Specifications

  • SoC – Bouffalo BL602 RISC-V processor @ up to 192 Mhz with 276KB RAM, 128KB ROM with WiFi and Bluetooth
  • Wireless
    • 2.4GHz 802.11b/g/n WiFI 4 up to 65 Mbps (802.11n) or 26 Mbps (802.11g)
    • Bluetooth LE 5.0
    • PCN antenna
  • 19x pin around module with
    • Up to 16x GPIO
    • 2x UART, 1x I2C, 1x SPI, 5x PWM
    • 10-bit DAC, 12-bit ADC
    • 1x EN
    • 1x SDIO
    • 3.3V and GND
  • Supply Voltage – 3.0 to 3.6V
  • Power consumption – Deep sleep mode: 22mA; deep standby mode: 2mA
  • Dimensions – 20 x 16 x 3mm
  • Temperature Range – -20°C to +85°C

DT-BL10 Block Diagram

Software Development

GitHub - Board Start Guide

GitHub - SDK & Tools

Document

GitHub - Board Development Manual


Buy Now

Comments

Post a Comment

Popular posts from this blog

Polos CH32VXX RISC-V Breakout Boards

-
Image
  Polos CH32VXX RISC-V Breakout Boards CH32V Series MCUs are designed by Qinheng Microelectronics Co., Ltd., focuses on connectivity technology and microprocessor research and is an IC design company. CH32V Series MCUs are low-cost & powerful functions like BT, USB2.0/3.0, CAN, I2C, SPI, USB PD and so on. So we develop the Polos CH32Vxx RISC-V Breakout Boards. Qinheng Provide C/C++ SDK, Arduino Library, and MRS IDE. We perfer to use Embedded Rust, We will support Embedded Rust development in CH32Vxx RISC-V MCU. Polos CH32V003 Breakout Alef - Features Main Chip Type: CH32V003F4U6 with QFN20 Package QingKe 32-bit RISC-V2A processor, Up to 48MHz frequency 2KB SRAM, 16KB Flash, 3.3/5V Power Supply 1 ch DMA, 1 group of OP Amp, 1 group of 10-bit ADC 16 bit timer x 2 USARTx1, I2Cx1, SPIx1 18 I/O ports, mapping an external interrupt 64-bit chip unique ID 1-wire serial debug interface (SDI) Polos CH32V203F8 Breakout Alef - Features Main Chip Type: CH32V203F8P6 with TSSOP20 Package Qingk...
Read more

Amnos CH347T Breakout

-
Image
  Amnos CH347T Breakout Overview Amnos CH347T Breakout is developed by XPU Labs, a subsidiary of AnalogLamb.Com. CH347 is a high speed USB converter interface chip, can provide USB to UART, I2C, SPI, JTAG, GPIO functions. Amnos CH347T Breakout's size is 40x40mm. It supports USB to two UARTs, It is used to program ESP32, integrate esp32 auto-download circuit. And it is used to program Xilinx FPGA with USB to JTAG function. It can also program EEPROM or Flash with USB to I2C/SPI function. Specifications USB2.0 high-speed device with a bandwidth of 480Mbps High-speed dual serial ports support up to 9Mbps baud rate Integrate ESP32 auto-download Function with USB to UART JTAG interface, 4-wire standard JTAG protocol, high-speed transmission, up to 60MHz Program Xilinx FPGA to RAM or FLASH with USB to JTAG I2C interface, can be used to operate EEPROM or various sensors SPI interface supports 2 chip selection signals, the highest frequency can reach 36MHz Several GPIOs can be used with US...
Read more

ALB32-WROVER - 64Mb Flash , 32Mb PSRAM ESP32-WROOM Module

-
Image
Pre-Order Now Hello, Welcome to AnalogLamb Blogger. AnalogLamb is a online shop for ESP32 Modules & Boards, IoT Application Kits. We are glad to sharing our ideas, R&D process and lessons or experience we get. Today I will introduce our new ESP32 modules - ALB32-WROVER. What is the Features - ALB32-WROVER? ESP32 Wi-Fi and Bluetooth combo chip inside. 64Mb Flash 32Mb PSRAM Pins to Pins Compatible with  ESP-WROOM-32 completely Community Education Module Size: 18 x 25 x 3 mm It is the top side of ALB32-WROVER module. You have noted that. We can use the shield of  ESP-WROOM-32(only has 32Mb Flash). But It has 64Mb Flash, 32Mb PSRAM. It is very easy to mount it on any  ESP-WROOM-32 board. It is the bottom side of ALB32-WROVER module. The Pins and dimension are same with  ESP-WROOM-32 Completely. Now we are testing the module. And Plan to release  ALB32-WROVER module on Aug. 2017. You can pre-order it now. ...
Read more